Parson Seal-Tite

Parson Seal-Tite is a moisture-insensitive, two-component, fast-reacting hydrophobic polyurethane grout designed to stop high-volume active leaks in manholes, pump stations and other wastewater structures. Parson Seal-Tite is packaged in a dual cartridge with a static mixer and is injected at or near the source of the leak, using a manual, dual-component caulk gun. The product contains no solvents, CFCs or HFCs.

ADVANTAGES
-Cures to a dense, rigid mass in approximately 30 seconds
-Chemically resistant
-Can fill large holes and voids
-Stops leaks up to 50 gpm
-Will not shrink
-Non-hazardous — 100% solids
-Environmentally friendly
-Excellent bond strength
-Will expand to 10 – 12 times liquid volume

Parson Hydro Grout

Parson Hydro Grout is a tough, low-viscosity, hydrophobic polyurethane grout, which when mixed with predetermined amounts of Parson Grout Accelerator, has reaction times from 30 seconds to 3 minutes. Parson Hydro Grout can be used to stop medium to high volume active leaks through cracks in manholes, pump stations, water and wastewater tanks, concrete pipes and other concrete and masonry structures.

ADVANTAGES
-Cures to a closed-cell foam
-Chemically resistant
-Fills voids and holes
-Low viscosity allows good penetration into small cracks
-Non-hazardous
-Environmentally friendly

Parson Perma Seal

Parson Perma Seal is a single component, hydrophilic polyurethane grout. It contains no TDI or solvents and has excellent elongation and flexibility properties. Reaction time, when mixed 1:1 with water, is approximately 30 seconds. Parson Perma Seal can be used to stop low to medium volume active leaks in manholes, pump stations, water and wastewater tanks, concrete pipes and other concrete and masonry structures.

ADVANTAGES
-Chemically resistant
-Great adhesion
-Stops active leaks
-Non-hazardous
-Environmentally friendly
-High elongation
-Excellent flexibility
-Easy to use

Parson RPM

Parson RPM is a rapid-setting, fiber-reinforced, calcium aluminate, cement-patching material that is sulfate resistant and may be used to repair manhole inverts, voids or cracks.

ADVANTAGES
-Simple to use — just add clean, potable water
-Non-shrink
-Excellent freeze-thaw resistance
-High early strength
-Full set in approximately 30 minutes
-High elongation
-Excellent flexibility
-Easy to use

Parson MH Liner

Parson MH Liner is a high-strength, fiber-reinforced, Portland cement based, microsilica-enhanced mortar for use in rehabilitating manholes, lift stations, wet wells and other wastewater structures.

ADVANTAGES
-Cost-effective alternative to replacement
-Stops infiltration and exfiltration
-Restores structural integrity
-Provides low to moderate corrosion protection
-High strengths and low permeability
-Excellent bond to damp surfaces
-Apply up to 3″ in a single coat
-Spincast, spray gun or trowel application

CA Liner 100

Parson CA Liner 100 is a high-strength, fiber-reinforced, microsilica-enhanced, 100% calcium aluminate cement with select, graded aggregates for use in rehabilitating manholes, lift stations, wet wells and other wastewater related structures.

ADVANTAGES
-Cost-effective alternative to replacement
-Stops infiltration and exfiltration
-Restores structural integrity
-Provides moderate to high corrosion protection
-High strengths and low permeability
-Excellent bond to damp surfaces
-Apply up to 2″ in a single coat
-Spincast, spray gun or trowel application

ConBlock MIC

This is a liquid additive for Parson MH Liner and Parson CA Liner 100 to eliminate the growth of bacteria that causes microbial induced corrosion (MIC) in manholes and other similar structures.

As a concrete treatment, ConBlock MIC is extremely effective against mold, fungi, algae and damaging bacteria. Unlike sacrificial or leaching chemistries, the technology of ConBlock MIC controls microorganisms with a chemistry that remains a permanent part of the concrete structure. The active ingredient in Con Block MIC – 3-(trihydroxysily!) propyldimethyloctadecyl ammonium chloride – relies on a charged ion and a unique spiked molecular structure to create an uninhabitable environment for the microorganisms. These molecular spikes are undetectable to human touch but overmatch single-cell organisms. In nature, most microbes carry the opposite ionic charge, so they are physically and irresistibly drawn into contact with ConBlock MIC, which punctures the cell walls of the offending microbes.

CA Liner 100+

Parson CA Liner 100+ is a high-strength, fiber-reinforced, microsilica-enhanced, pure-fused calcium aluminate cement and calcium aluminate aggregate mortar designed to rehabilitate and protect new and existing manholes, lift stations, wet wells and other wastewater related structures against H2S attack.

ADVANTAGES
-Cost–effective alternative to replacement
-Stops infiltration and exfiltration
-Restores structural integrity
-Provides a high level of corrosion protection
-High early and 28-day strengths
-Freeze-thaw resistant
-Low permeability
-Excellent bond to damp surfaces
-Apply up to 2″ in a single coat
-Spincast, spray gun or trowel application

SL100-B Silane Sealer

SL100 is a 100% penetrating silane sealer. It is formulated to be a clear, breathable, long-lasting, 100% silane, water repellent sealer to achieve the highest depth of penetration.

SL100-B Silane Sealer

Technical Data Sheets

Description

SL100 is a 100% penetrating silane sealer. It is formulated to be a clear, breathable, long-lasting, 100% silane, water repellent sealer to achieve the highest depth of penetration.

Packaging

5 gallon (18.9 L) pails and 55 gallon (208 L) drums

Yield

250–400 ft2/gallon (6–10 m2/L)

Curing

Typical curing time for SL100 is 4–6 hours at 70°F (21°C) and 50% relative humidity. Cooler temperatures or higher relative humidity can extend the drying time.

Storage

Store in unopened containers in a clean, dry area between 35-110°F (2-43°C). Keep from freezing.

Shelf Life

18 months when properly stored

Clean Up

Clean equipment with xylene.

Warranty

Quadex® warrants this product to be free from manufacturing defects and to meet the technical properties, contained on the Technical Data Sheet, if used as directed within shelf life. Satisfactory results depend not only on quality products but also upon many factors beyond our control. The only remedy for the Purchaser for any claim concerning this product, including but not limited to, claims alleging breach of warranty, negligence, strict liability or otherwise, is the replacement of product or refund of the purchase price, at the sole option of Quadex.

Any claims concerning this product must be received in writing within one (1) year from the date of shipment. All further technical advice is based on Quadex’s present knowledge and experience. Quadex assumes no liability for providing such information and advice including the extent to which such information and advice may  relate  to  existing  third party intellectual property rights, especially patent rights, nor shall any legal relationship be created by or arise from the provision of such information and advice. Quadex reserves the right to make any changes according to technological progress or further developments.

The Purchaser must test the product for suitability for the intended application and purpose before proceeding with a full application. Performance of the product described herein should be verified by testing and carried out by qualified experts.

K100 Flex Polyaspartic Coating

K100FLEX is a low viscosity, high-solids aliphatic polyisocyanate hardener and polyaspartic coating system. K100FLEX is a self-leveling system featuring fast cure, excellent adhesion, and high-film build. The system can be used for both decorative and protective applications as it exhibits outdoor durability, chemical resistance, skydrol resistance, and light-fastness as well as high gloss and color retention.

K100 Flex Polyaspartic Coating

Technical Data Sheets

K100 Flex Polyaspartic Coating

Safety Data Sheets

Description

K100FLEX is a low viscosity, high-solids aliphatic polyisocyanate hardener and polyaspartic coating system. K100FLEX is a self-leveling system featuring fast cure, excellent adhesion, and high-film build. The system can be used for both decorative and protective applications as it exhibits outdoor durability, chemical resistance, skydrol resistance, and light-fastness as well as high gloss and color retention. The material is applied in single or multiple coats by brush, roller or squeegee to vary thicknesses to a variety of substrates including concrete and metal. It can be applied as a top coat employed within multi-build chip/ quartz seamless coating systems.

K100FLEX provides excellent impact, abrasion, and chemical resistance characteristics. Suitable for high traffic interior or exterior applications, the material is ideal for clear topcoat sealer applications over commercial applications, industrial facilities, swimming pool decks, and parking garages.

Packaging

2 gallon kit, 10 gallon kit, 100 gallon kit

Mixing Directions

Mixing Part A with Part B: Mix K100S92 and H92Flex in equal parts (1:1) using a clean, dry working vessel. Use a paddle mixer on slow speed for 2 minutes. Avoid overmixing or creating a vortex that would introduce air. Do not mix below the dew point, which will shorten the pot life. No induction time is required prior to use. If micro-media agents are to be incorporated, they are to be added after thoroughly.

Application

Suggested application thickness is 8 mils or 200 ft per coat, per gallon. Refer to Quadex® tech docs directly for specifics on effective application techniques. Maximum application mil thickness in a single application is 10-12 mils. Material will be dry to the touch 2-3 hours after application, dependent on ambient temperature, slab temperature and humidity. Product may be re-coated within 2-24 hours following application. Light foot traffic is acceptable 12 hours following application and vehicular traffic is acceptable 48 hours after application.

Clean Up

Use MEK or Acetone

Safety

Polyaspartic aliphatic polyurea products contain chemical ingredients that are considered hazardous. Read the container label warning and Safety Data Sheet prior to use.