E100 is a 100% solids, low viscosity, self-leveling epoxy coating with excellent adhesion to concrete and metal substrates. E100 can be used as a concrete sealer or as a topcoat. E100 can be used in chip and metallic systems and is compatible to K100FLEX.

3 gallon kit, 15 gallon kit, 150 gallon kit

Concrete structures must be cured a minimum of 28 days prior to application. Surfaces to be coated must be free of grease, standing water and any other contaminants that may impede adhesion. Always check the surface for any bond inhibitors prior to application. Any repairs must be addressed prior to application and should be repaired in accordance with ICRI standards. Concrete must have a surface profile of CSP #3. If concrete does not meet a profile of CSP #3 it must be profiled mechanically to meet CSP #3. Repair all cracks and joints prior to coating application. Bare metal substrates must be prepared to a SSPC SP 1 standard.

Note: Maintaining a consistent storage temperature prior to application will maximize working time. Material should be kept in a cool dry place prior to application.

Mixing Part A with Part B: Mix 2 parts E100 to 1 part EZ150. Mix for 3 minutes. No induction time is required prior to use. If micro-media agents are to be incorporated, they are to be added after thoroughly mixing A and B.

Suggested application thickness is 8 mils or 200 ft per coat, per gallon. Refer to Quadex® tech docs directly for specifics on effective application techniques. Maximum application mil thickness in a single application is 10-12 mils. Material will be dry to the touch 4 hours after application, dependent on ambient temperature, slab temperature and humidity. Product may be re-coated within 4-24 hours following application. Light foot traffic is acceptable 12 hours following application and vehicular traffic is acceptable 48 hours after application.

Use MEK or Acetone

PE-21 is a Polyester Urethane with a simultaneous moisture curing component that provides the most durable, chemical resistant, UV stable coating on the market.

• HVLP
• Pressure Pot
• Airless sprayer

Some materials in this product may cause skin and eye irritation and/or sensitization or other allergic responses upon repeated contact. This product must be handled with extreme care and in strict adherence to good industrial practices. Before using it or any other product referred to in this bulletin, consult the applicable Safety Data Sheets for appropriate handling procedures and protective equipment.

E21 is a high build low VOC epoxy primer designed with superior adhesion to steel, aluminum and concrete. Excellent corrosion resistance and quick flash times.

Use Quadex® S-440 wax and grease remover to clean metal substrate free of grease, dirt and foreign contaminants. Concrete must be a minimum of an SSPC 2.

• HVLP 1.5mm-1.8mm (10psi at cap)
• Pressure Pot
• Airless sprayer

Quadex I&I Guard®-MSF (Soil Stabilization Foam) is a low viscosity, polyurethane injection resin, designed to stabilize soil. When mixed with catalyst and injected, it migrates through loose soil and into below-grade voids. As it comes into contact with moisture in the soil, I&I Guard-MSF reacts and expands to form a rigid foam. The foam encapsulates loose soil, fills voids, and forms a solid, watertight barrier.

5 Gallon Pails (18.9 Liter Pail).

Keep temperature of chemicals at 70°F for several days before use. Cold chemicals can cause poor mixing, pump cavitation or other process problems due to higher viscosity at lower temperatures. Absolutely no thinners should be added to this 100% solids system. Viscosity can be reduced by an increase in temperature. The ‘A’ component is sensitive to exposure to moisture. Keep drums tightly closed when not in use and under nitrogen pressure of 2 – 3 psi after they have been opened. Prolonged exposure to temperatures below 50°F can cause the ‘A’ component to freeze. Do not store in direct sunlight.

Quadex® Quad-Clean™ removes cured resin from metal components such as tools and equipment. For best results, use an industrial grade ultrasonic cleaner with built in heater.

5 Gallon Pails (18.9 Liter Pail).

Store in dry environment between 40°-80°F (10°-26°C). No shelf life.

Soak metal or Teflon components in Quad-Clean using a metal, glass or ceramic container until cured material softens. All wetted parts and lid must be metal (no plastic). Heat to 100-150°F. Only do this in a well ventilated area as heating the material increases solvent vapors. Remove hot parts with metal tongs. Periodically remove components from the solution and scrape off cured resin. Repeat as necessary. Once components are sufficiently clean, remove them, rinse with water or a mild solvent, and wipe down with a dry cloth. If there is no ultrasonic cleaner available, heat the Quad-Clean and components in a crock pot to 100-150°F. Follow directions and cautions above.

Avoid contact with eyes and skin, always use personal protective equipment in compliance with local regulations. Read the relevant Safety Data Sheet before use.

Structure Guard®-QS is a quick spray, 100% solids, high-build epoxy coating formulated to provide long-term corrosion protection and structural enhancement for manholes, pump stations, treatment plants or any wastewater infrastructure subject to high levels of corrosion and/or abrasion. Structure Guard-QS sets fast for a quick return-to-service in the most aggressive and turbulent environments. It finishes smooth to enhance flow and is utilized as an interior or exterior pipe lining.

With Structure Guard®-QS, only 1 coat is needed to attain finished thickness. If additional coats are called for they must be applied before the previous coat has completely cross-linked, typically for 12 hours @ 72°F (higher temperatures/humidity will shorten this window). If re-coating is needed, brush blast before applying the next coat. Before re-coating, clean and dry surface thoroughly to remove all contamination, including amine blush or condensation. Small areas may be abraded by sanding or wire brushing.

The same requirements apply when overlapping seams of adjacent coating sections to create a continuous protective film. If the coating surface to be overlapped at the seam cannot be brush blasted, use a non-impact means, such as power brushing or sanding, to create adequate mechanical profile.

Structure Guard-QS will yield theoretical coverage of 20 sq. ft per gallon @ 80 mils thickness. Actual surface coverage will depend on substrate porosity and roughness. A wet film thickness gauge may be used to determine actual coating thickness.

Flex Guard®-LV is an injectable flexible epoxy resin design to be injected into cracks in concrete. With a 100-150% elongation it is ideal for freeze/thaw and structures that experience temperature fluxution.

600×600 ml cartridge

1:1 in premeasured cartridge

Use only after Flex Guard®-FM and ports have been applied. Mechanical grinding is required prior to application of Flex Guard-LV. Use 80 grit diamonds to achieve a CSP#3 profile. Use grinder to remove any loose concrete. Smooth edges of crack. Plow crack out with a air blower. Substrate must be free of grease, standing water and other contaminants that may impede adhesion. Always check the surface for any bond inhibitors prior to application.

Remove nut and plug from the cartridge. Attach static mixing tip to cartridge. Place cartidge in dispensing gun. Pull trigger on dispensing gun and burn 2 oz into a cup. Insert mixing tip into port and pull trigger to start dispensing product. When Flex Guard-LV reaches the subsequent port stop dispensing product. Place cap in the port and move to the next port and repeat process.

Acetone or MEK

I&I Guard^®-SSF is a high density, high strength, structural two-part polyurethane grout. This closed cell polyurethane’s low viscosity and hydro insensitive nature allows for permeation filling voids, undersealing concrete, and stabilizing soil while also mitigating inflow and infiltration.

10 gallon unit, 100 gallon units

Insert probes in grid pattern to area of desired application. Begin injecting into first probe avoiding over pressuring while taking note of volumes used and travel of foam. Make sure material is not exiting or penetrating other probes while taking into consideration volume to vertical distance ratio estimation. Purge injection gun frequently to avoid the material curing within the gun. Clean injection gun thoroughly after use.

Always use safety glasses and protective clothing including gloves when using this product to avoid contact with skin and eyes. Before use review respective Safety Data Sheet.

I & I Guard® – SCF 200 is a single component, moisture-activated and MDI/TDI blended polyurethane injection grout designed for sealing persistent water leaks caused by large cracks or ill-fitting joints in concrete structures. I & I Guard® – SCF 200 is capable of absorbing up to 12x its weight in water. Foam consistency, 1:1 water ratio. Gel consistency, 10:1 water ratio.

Ideal for manholes, tunnels, pipes, vaults and tanks of all construction materials.

Product packaged by weight based on specific gravity.

• Drum: Net Wt. 484 lbs. (220 kg)

• Pail: Net Wt. 44 lbs. (20 kg)

• Gallon: Net Wt. 8 lbs. (3.6 kg)

• Cartridge: ~10.114 fl. oz. (~ 300 ml)

Store in temperatures ranging from 45°F – 95°F (7°C – 35°C) in a dry environment. Container must remain tightly closed when not in use. Contents are packaged under dry nitrogen to keep moisture out and extend product shelf life.

Recommended for active, high-volume water flow, where large cracks, voids or joints in concrete structures, must be sealed. Effective solution to stabilize moving cracks and joints caused by freeze/thaw conditions and other forms of external pressure.