I & I Guard® – SCF 200 is a single component, moisture-activated and MDI/TDI blended polyurethane injection grout designed for sealing persistent water leaks caused by large cracks or ill-fitting joints in concrete structures. I & I Guard® – SCF 200 is capable of absorbing up to 12x its weight in water. Foam consistency, 1:1 water ratio. Gel consistency, 10:1 water ratio.

Ideal for manholes, tunnels, pipes, vaults and tanks of all construction materials.

Product packaged by weight based on specific gravity.

• Drum: Net Wt. 484 lbs. (220 kg)

• Pail: Net Wt. 44 lbs. (20 kg)

• Gallon: Net Wt. 8 lbs. (3.6 kg)

• Cartridge: ~10.114 fl. oz. (~ 300 ml)

Store in temperatures ranging from 45°F – 95°F (7°C – 35°C) in a dry environment. Container must remain tightly closed when not in use. Contents are packaged under dry nitrogen to keep moisture out and extend product shelf life.

Recommended for active, high-volume water flow, where large cracks, voids or joints in concrete structures, must be sealed. Effective solution to stabilize moving cracks and joints caused by freeze/thaw conditions and other forms of external pressure.

Quadex® Quad-Clean™ removes cured resin from metal components such as tools and equipment. For best results, use an industrial grade ultrasonic cleaner with built in heater.

5 Gallon Pails (18.9 Liter Pail).

Store in dry environment between 40°-80°F (10°-26°C). No shelf life.

Soak metal or Teflon components in Quad-Clean using a metal, glass or ceramic container until cured material softens. All wetted parts and lid must be metal (no plastic). Heat to 100-150°F. Only do this in a well ventilated area as heating the material increases solvent vapors. Remove hot parts with metal tongs. Periodically remove components from the solution and scrape off cured resin. Repeat as necessary. Once components are sufficiently clean, remove them, rinse with water or a mild solvent, and wipe down with a dry cloth. If there is no ultrasonic cleaner available, heat the Quad-Clean and components in a crock pot to 100-150°F. Follow directions and cautions above.

Avoid contact with eyes and skin, always use personal protective equipment in compliance with local regulations. Read the relevant Safety Data Sheet before use.

Quadex I&I Guard®-MSF (Soil Stabilization Foam) is a low viscosity, polyurethane injection resin, designed to stabilize soil. When mixed with catalyst and injected, it migrates through loose soil and into below-grade voids. As it comes into contact with moisture in the soil, I&I Guard-MSF reacts and expands to form a rigid foam. The foam encapsulates loose soil, fills voids, and forms a solid, watertight barrier.

5 Gallon Pails (18.9 Liter Pail).

Keep temperature of chemicals at 70°F for several days before use. Cold chemicals can cause poor mixing, pump cavitation or other process problems due to higher viscosity at lower temperatures. Absolutely no thinners should be added to this 100% solids system. Viscosity can be reduced by an increase in temperature. The ‘A’ component is sensitive to exposure to moisture. Keep drums tightly closed when not in use and under nitrogen pressure of 2 – 3 psi after they have been opened. Prolonged exposure to temperatures below 50°F can cause the ‘A’ component to freeze. Do not store in direct sunlight.

I & I Guard® – SCF 200 is a single component, moisture-activated and MDI/TDI blended polyurethane injection grout designed for sealing persistent water leaks caused by large cracks or ill-fitting joints in concrete structures. I & I Guard® – SCF 200 is capable of absorbing up to 12x its weight in water. Foam consistency, 1:1 water ratio. Gel consistency, 10:1 water ratio.

Ideal for manholes, tunnels, pipes, vaults and tanks of all construction materials.

Product packaged by weight based on specific gravity.

• Drum: Net Wt. 484 lbs. (220 kg)

• Pail: Net Wt. 44 lbs. (20 kg)

• Gallon: Net Wt. 8 lbs. (3.6 kg)

• Cartridge: ~10.114 fl. oz. (~ 300 ml)

Store in temperatures ranging from 45°F – 95°F (7°C – 35°C) in a dry environment. Container must remain tightly closed when not in use. Contents are packaged under dry nitrogen to keep moisture out and extend product shelf life.

Recommended for active, high-volume water flow, where large cracks, voids or joints in concrete structures, must be sealed. Effective solution to stabilize moving cracks and joints caused by freeze/thaw conditions and other forms of external pressure.

I&I Guard^®-SSF is a high density, high strength, structural two-part polyurethane grout. This closed cell polyurethane’s low viscosity and hydro insensitive nature allows for permeation filling voids, undersealing concrete, and stabilizing soil while also mitigating inflow and infiltration.

10 gallon unit, 100 gallon units

Insert probes in grid pattern to area of desired application. Begin injecting into first probe avoiding over pressuring while taking note of volumes used and travel of foam. Make sure material is not exiting or penetrating other probes while taking into consideration volume to vertical distance ratio estimation. Purge injection gun frequently to avoid the material curing within the gun. Clean injection gun thoroughly after use.

Always use safety glasses and protective clothing including gloves when using this product to avoid contact with skin and eyes. Before use review respective Safety Data Sheet.

I&I Guard^® is a two-part polyurethane grout used to stop high flow infiltration. Easy injection method creating curtain of grout on the outside of underground structures. Super fast cure allows for immediate reduction in infiltration. Best when used in conjunction with Quadex® Repair Materials rehab systems.

Case of (6) 300ml x 300ml or 600ml x 600ml cartridges

Store between 40°F and 100°F.

Drill 5/8” hole completely through the structure. Remove nut from cartridge. Slide nut onto static mixing tip. Insert static mixing tip into the drilled hole and insert cartridge into the Quadex® OneGun®. Remove cap plug from cartridge and hold the Quadex OneGun upright. Attach cartridge to static mixing tip by tightening the nut. Pull trigger on Quadex OneGun to dispense grout. Continue to pull trigger until the cartridge is empty or until the OneGun automatically seizes.

Always use safety glasses and protective clothing including gloves when using this product.