Quadex® Quad-Clean™ removes cured resin from metal components such as tools and equipment. For best results, use an industrial grade ultrasonic cleaner with built in heater.

5 Gallon Pails (18.9 Liter Pail).

Store in dry environment between 40°-80°F (10°-26°C). No shelf life.

Soak metal or Teflon components in Quad-Clean using a metal, glass or ceramic container until cured material softens. All wetted parts and lid must be metal (no plastic). Heat to 100-150°F. Only do this in a well ventilated area as heating the material increases solvent vapors. Remove hot parts with metal tongs. Periodically remove components from the solution and scrape off cured resin. Repeat as necessary. Once components are sufficiently clean, remove them, rinse with water or a mild solvent, and wipe down with a dry cloth. If there is no ultrasonic cleaner available, heat the Quad-Clean and components in a crock pot to 100-150°F. Follow directions and cautions above.

Avoid contact with eyes and skin, always use personal protective equipment in compliance with local regulations. Read the relevant Safety Data Sheet before use.

A silicate resin formulated for sectional liners suited for isolated
pipe repair and patching. We offer three different silicate resins
designed for fast, medium and slow cure times that range from
15-100 minutes.

Quad-Cure® 3120/3145 CIPP Resin is a 100% solids epoxy system designed to meet all specifications for full structural Cured-In-Place Pipe (CIPP) liner conforming to ASTM F1216. Using Quadex’s QB31 Base Resin, in conjunction with QX Hardeners, Quad-Cure 3120/3145 will achieve a fully cross-linked system to for a high quality, long-term solution.

It is important to note that Quad-Cure 3120/3145 is specifically designed for CIPP applications and has not been modified from another industry resin in attempt to fit the complex environmental, design and performance needs required in underground rehabilitation industry.

QB31 – Quad-Cure 100% Solids Base Resin
QX3120 – 20 Pot Life Hardener
QX3145 – 45 Pot Life Hardener

3 parts QB31 to 1 part QX3120/QX3145.

Mix 3 parts QB31 Epoxy Base to 1 part QX3120/QX3145. Mix using a mixing paddle for a minimum of 3 minutes.

18 months unopened and stored between 50°F and 100°F.

Store between 40°F and 100°F.

Disposal must conform to local and state regulations.

Always use safety glasses and protective clothing including gloves when using this product. QX3120/QX3145 contains Amine. Do not ingest. If QX3120/QX3145 comes in contact with eyes flush immediately with water. Always read the container label warning and Safety Data Sheet prior to use.

Quad-Cure® UV is a low viscosity, highly reactive UV curing resin based on methacrylate esters. The resin is styrene free and considered an excellent solution for colder and more environmentally sensitive conditions.

The chemical composition of Quad-Cure UV ensures good chemical resistance performance. All the components have high flash point (>95°C), which guarantees no VOC emissions or strong odor.

Quad-Cure UV resin already contains the required amount of photoinitiator. For proper curing, the resin must be irradiated by UV light (at least 10 mW/cm2 from about 5 cm distance). The applied initiator allows the use of high pressure mercury lamps or UV-LEDs for curing.

Quad-Cure UV resin should be stored indoors in the original, unopened and undamaged packaging, in a dry place at temperatures between 5°C and 30°C. Properties might slightly change during storage. Store in dark and in 100% light tight containers only. Avoid contact of the resin with day light during handling operations as day light may lead to immediate curing reactions.

Product must be stirred before using.

A Safety Data Sheet is available on request.

Test methods are available on request.

Quad-Cure^® CIPP Resin is a 100% solids epoxy system designed to meet all specifications for full structural Cured-In-Place Pipe (CIPP) liner conforming to ASTM F1216. Using Quadex’s QB Base Resin, in conjunction with QX Hardeners, Quad-Cure will achieve a fully cross-linked system to for a high quality, long- term solution.

It is important to note that Quad-Cure is specifically designed for CIPP applications and has not been modified from another industry resin in attempt to fit the complex environmental, design and performance needs required in underground rehabilitation industry.

4 parts QB41 to 1 part QX4130 / QX4160.

Always use safety glasses and protective clothing including gloves when using this product. QX4130/QX4160 contains Amine. Do not ingest. If QX4130/QX4160 comes in contact with eyes flush immediately with water. Always read the container label warning and Safety Data Sheet prior to use.

Mix 4 parts QB41 Epoxy Base to 1 part QX4130 / QX4160. Mix using a mixing paddle for a minimum of 3 minutes.

18 months unopened and stored between 50°F and 100°F.

Store between 40°F and 100°F.

Disposal must conform to local and state regulations.

Quad-Cure® LC is a styrene-free product formulated to provide extended pot life and working time in the field to assure quality installation of CIPP liners. Quadex® Latent Cure technology allows for a longer working time without sacrificing fast cure times. Quad-Cure LC has been formulated with different pot life’s to best meet the demands of difficult lining projects. It can also be refrigerated at 5°C/ 41°F transported to the jobsite for large diameter CIPP applications.

Pour Part B in to Part A at the ratio indicated on the chart. Use a drill with a mixing blade, for a minimum of 3 minutes. Mixture must be consistent in color to assure a full mix. Store at 21°C/70°F for 24 hours before impregnating liner.